Stormworks: Build and Rescue

Stormworks: Build and Rescue

42 次評價
Rescue Dragon
2
   
獎勵
加入最愛
已加入最愛
移除最愛
檔案大小
發佈於
更新時間
2.818 MB
2023 年 10 月 8 日 上午 12:08
8 月 18 日 下午 12:28
10 項更新註記 (檢視)

訂閱以下載
Rescue Dragon

在 Richman 的 2 個收藏中
Richman's Modular Container Systems
20 個項目
NFT (New Gen. Frequency Technology)
12 個項目
描述
The Rescue Dragon
Overview
Based on the versatile airframe of the Combat Dragon, the Rescue Dragon covers a heavy requested market niche with a capable workhorse with endurance.

For a full description and detailed checklist refer to the Rescue Dragon's official Flight Manual:
Rescue Dragon - Flight Manual[drive.google.com]

Features
The Rescue Dragon features a wide set of systems and sensor to fit into the theater of archipelagean offshore rescue. With a huge airtime thanks to it's efficient engines, it's designed to leverage the balance of life and death in Dragon's favor.

Nominally and most efficiently operated by 2 crew (pilot + operator). With it's auto-pilot systems, the Dragon can also be employed single piloted. It features the following list of systems (not exclusive):
  • Autopilot with POS, HDG, NAV (Waypoint) and ALT-Hold modes. POS-Hold can be adjusted by winch-operator
  • GPWS (Ground Proximity Warning System)
  • A modern FLIR optical turret with ground and radar tracking, water cannon and a slaved search light
  • A simple transponder locator
  • VDF system to locate radio sources (with known frequencies)
  • Dual deployable four-winch systems with changeable harness or stretchers
  • Weather Logger for metreological situational awareness
  • A simple sonar underwater detection system
  • WIPEOUT Client
  • 8 intensive care medical beds
  • 7 seats for crew or pax
  • A large winch for heavy lifting (or deep sea support)
  • An integrated container grappler
  • A wide variety of rescuing equipment

With the same hull as the Combat Dragon, the Rescue Dragon is also cabable of water landing. But beware of high winds!

With a topspeed of 80m/s and an endurance of numerous hours it easely fits any demand. And with it's safety systems, crew well beeing is severly enhanced even in the harshest environments.

Specs
Mass
20'254
Cost
$ 218'200.-
Tank capacity (Jet A-1)
>12'000 L
Range
>1000 km
Top Speed
80 m/s
Minimum Workbench Size
Large Hangar / Large Dock

Operation
For a full description and detailed checklist refer to the Rescue Dragon's official Flight Manual:
Rescue Dragon - Flight Manual[drive.google.com]

Quickstart
  1. Switch ON Bat1/2 and Gen1/2
  2. Start Engines
  3. Activate Inter-Shaft
  4. Release Brakes (col.) if required
  5. Taxi with minimal Forward-Thrust (5)
  6. Lift Collective to take off

WARNING:
Avoid flight with Inter-Shaft OFF. Single engine failure can lead to rapid loss of control!

Related Content
The Dragon - Heavy Assault Gunship
PFD-300 Avionics Package by mitsubishimax9
Simple ND by Richman
Fuel Display by Richman
RadarMap by Richman
Weather Logger by Richman
Simple Sonar by Richman
Monitor Brightness Controller by Richman
WIPEOUT Client by MATTH3X
22 則留言
Richman  [作者] 9 月 9 日 下午 11:52 
Just reset the set altitude by reactivating ALT hold. The collective can then be used for fine tuning.
axolotl_person 9 月 9 日 下午 3:22 
Great vehicle otherwise
axolotl_person 9 月 9 日 下午 3:22 
With the current collective system you cannot go down very far in alt hold mode
Harveycarmichael 8 月 27 日 上午 10:09 
is used it and it was good ima leave a five star rating
Richman  [作者] 7 月 24 日 上午 11:46 
I maybe add something like this in a future avionics upgrade. ;-)
MrNerf2632 7 月 24 日 上午 11:33 
A separate override would be nice
MrNerf2632 7 月 24 日 上午 11:33 
Yeah but then in cant hover itself over a waypoint
Richman  [作者] 7 月 24 日 上午 6:19 
It's just conditional, as it is common in aviation. If you're hovering, there's no sense in activating a NAV AP, and vice versa.

It should be outlined in the Flight Manual in a - hopefully - understanable manner. 😉
MrNerf2632 7 月 23 日 下午 8:19 
Figured it out... Kinda wonky activation though.
MrNerf2632 7 月 23 日 下午 8:06 
Autopilot button not working? I press 1 and it only toggles on and off position hold... Am I doing something wrong?