Shopseite
Cities: Skylines
Alle Diskussionen Screenshots Artworks Übertragungen Videos Workshop Neuigkeiten Guides Rezensionen

Cities: Skylines

Shopseite
Cities: Skylines >  Workshop > Workshop von VecchioChristo
153 Bewertungen
VC Rough Industrial Quay
Beschreibung Diskussionen0 Kommentare20 Änderungen
   
Preis verleihen
Favorisieren
Favorisiert
Entfernen
Assets: Road
Dateigröße
Veröffentlicht
12.284 MB
21. Dez. 2021 um 9:30
1 Änderungshinweis (anzeigen)
Benötigte Inhalte
Dieser Inhalt erfordert alle der folgenden weiteren Inhalte
Erstellt von
VecchioChristo
Offline
Alle 856 Kollektionen von VecchioChristo und anderen Leuten ansehen (ohne versteckte Kollektionen)
16,804 Einzelaufrufe
4,834 Aktuelle Abonnenten
510 Aktuelle Favoriten

Abonnieren zum Herunterladen
VC Rough Industrial Quay

In 1 Kollektion von VecchioChristo
Lake Thun required Mods and Assets
76 Inhalte
Beschreibung
VC Rough Industrial Quay by VecchioChristo

A narrow quay with tight bending corners to facilitate use in tight or confined areas.
Narrow quays such as this can cause ground spikes on the water side to rise up on the face of the quay. Use the Terreforming Networks by Sp3ctre18 to hold these down.

Terraforming Network Extended (pack)
20 Kommentare
< >
VecchioChristo  [Autor] 10. Jan. 2022 um 4:03 
Quays this narrow are less than or near the width of the underlying ground mesh. So the ground mesh has difficulty conforming to the rapid change in slope. I would assume this is why the vanilla quays are so wide. Way beyond what could be considered scale.
Helshad 10. Jan. 2022 um 3:28 
Ah, my bad. I´ll figure out another way to use it later then. :) *goes back to read the instructions one more time* I think I read it... but forgot about it.
VecchioChristo  [Autor] 9. Jan. 2022 um 8:00 
you might want to read the previous comments. This quay is narrow for more tight places. place a .5 meter terraforming network on the water side, adjust its distance from the quay then wiggle the quay a little bit and those gaps should disappear. This happens because the width of the quay is so narrow. You get these gaps with all quays, wider ones just cover it up
Helshad 9. Jan. 2022 um 7:38 
https://cdn.discordapp.com/attachments/268042746839695361/929760937932644432/unknown.png and here is a link to a picture showing what I mean.
Helshad 9. Jan. 2022 um 7:36 
I am seeing some glitches when I place this quay. On the inside of it, opposite the water, I can see through the ground along the entirety of the quay. Its like a 1 cm opening. If I pan around the camera from the other side I dont see it. Its only from the seaside I i see it.
melbchef2 25. Dez. 2021 um 20:01 
LOOKS SO MUCH BETTER FOR MY OIL DOCKS :-)
Bonovision 23. Dez. 2021 um 5:55 
@LDTailor using the terraforming networks is an exercise of fiddling as each segment depending on height, curves etc ends up unique. Play around with the different sizes as well.
Bonovision 23. Dez. 2021 um 5:53 
@VecchioChristo It's like you heard my right before bedtime tears and swooped in to save the day like Santa Claus!
VecchioChristo  [Autor] 21. Dez. 2021 um 20:08 
I get those gaps all the time, you just have to push and shove the quay a little to make them disappear.
LDtailor 21. Dez. 2021 um 20:01 
And thanks for the additional info. I'm not wot working on map editor at the moment. But will try the terraforming networks.