Strona w sklepie
Stormworks: Build and Rescue
Wszystko Dyskusje Zrzuty ekranu Prace graficzne Transmisje Wideo Warsztat Aktualności Poradniki Recenzje

Stormworks: Build and Rescue

Strona w sklepie
Stormworks: Build and Rescue >  Warsztat > Warsztat użytkownika Phil
Ocen: 31
Smooth RPS Limiter (Modular Engines and Prefabs)
Opis Dyskusje0 Komentarze30 Lista zmian
   
Przyznaj nagrodę
Ulubione
Ulubione
Usuń z ulubionych
Vehicles: Air, Sea, Land, Mechanical
Microcontrollers: Calculation, Fluid, Modular, Microcontroller
Tagi: v1.2.3
Rozmiar pliku
Zamieszczono
Zaktualizowano
164.550 KB
13 czerwca 2021 o 13:00
13 czerwca 2021 o 13:21
Listy zmian: 2 ( zobacz )
Twórca
Phil
Offline
Zobacz wszystkie kolekcje: 22 (niektóre mogą być ukryte)
2,826 Unikalni odwiedzający
1,378 Obecni subskrybenci
33 Obecne ulubione

Zasubskrybuj, aby pobrać
Smooth RPS Limiter (Modular Engines and Prefabs)

Opis
If you are unhappy with the 0.5 method consisting in cutting the throttle in half if the RPS are above the set limit, try out this Microcontroller! (No PID inside!)
With this smooth approach you can get a more continuous engine throttle resulting in less fuel consumption and heat generation as well as less unpleasant engine noise.

You can enable variable RPS limit to change that limit in-game while on the move.
A hardness factor is determined by your set RPS limit to keep the resulting RPS from overshooting more than 1. You can manually increase that factor if you want to be closer to the RPS limit.

This controller works on no load engines too but is meant for engines under load like vehicle engines.
Komentarzy: 30
< >
Phil  [autor] 3 lipca o 7:12 
Throttle is throttle, you need to add fuel manifold throttle which without supercharge can just be half of the air throttle.
CatLover2500 2 lipca o 13:34 
Does it work with modular engines?
__MRX__ 31 marca o 6:20 
you should add idle rps
Firegecko 14 grudnia 2023 o 0:16 
Awesome. Just what i was needing. Thanks heaps!
Decadenced 6 sierpnia 2023 o 10:25 
works fine 4 me, thank u
Phil  [autor] 28 czerwca 2023 o 9:56 
No it doesn't, just an RPS limiter like the name says, not an ECU. To idle engine you could just switchbox to a PID with P of 0.3.
buder28 27 czerwca 2023 o 14:16 
that mcu dosent have any kind of idling controll last time i tested
you will need to figure that out
Ninovium 27 czerwca 2023 o 13:39 
btw if you connect an actual throttle to the controller, then the engine just goes to 1 rps and dies. If you connect to W/S, it revs the engine to the max until it explodes. (it also implodes your ear drums)
Ninovium 27 czerwca 2023 o 13:37 
I have the same problem as the guy below, could you show us how to actually connect it? (to help idiots like myself)
BasicallyIPlayGames 8 czerwca 2023 o 20:47 
Other than its set up with W/S but I'd imagine it should still work set up like that still.