Σελίδα Καταστήματος
Stormworks: Build and Rescue
Όλα Συζητήσεις Στιγμιότυπα Εικόνες Μεταδόσεις Βίντεο Εργαστήρι Νέα Οδηγοί Κριτικές

Stormworks: Build and Rescue

Σελίδα Καταστήματος
Stormworks: Build and Rescue >  Εργαστήρι > Εργαστήρι του χρήστη Phil
31 ψήφοι
Smooth RPS Limiter (Modular Engines and Prefabs)
Περιγραφή Συζητήσεις0 Σχόλια30 Ενημερώσεις
   
Βραβείο
Αγαπημένο
Αγαπημένο
Μη αγαπημένο
Vehicles: Air, Sea, Land, Mechanical
Microcontrollers: Calculation, Fluid, Modular, Microcontroller
Ετικέτες: v1.2.3
Μέγεθος αρχείου
Αναρτήθηκε
Ενημερώθηκε
164.550 KB
13 Ιουν 2021, 13:00
13 Ιουν 2021, 13:21
2 σημειώσεις αλλαγών ( προβολή )
ΔΗΜΙΟΥΡΓΗΘΗΚΕ ΑΠΟ
Phil
Εκτός σύνδεσης
Προβολή και των 20 συλλογών (μερικές μπορεί να είναι κρυφές)
2,684 Μοναδικοί επισκέπτες
1,327 Τωρινοί συνδρομητές
30 Αγαπημένο τώρα

Συνδρομή για λήψη
Smooth RPS Limiter (Modular Engines and Prefabs)

ΠΕΡΙΓΡΑΦΗ
If you are unhappy with the 0.5 method consisting in cutting the throttle in half if the RPS are above the set limit, try out this Microcontroller! (No PID inside!)
With this smooth approach you can get a more continuous engine throttle resulting in less fuel consumption and heat generation as well as less unpleasant engine noise.

You can enable variable RPS limit to change that limit in-game while on the move.
A hardness factor is determined by your set RPS limit to keep the resulting RPS from overshooting more than 1. You can manually increase that factor if you want to be closer to the RPS limit.

This controller works on no load engines too but is meant for engines under load like vehicle engines.
30 σχόλια
< >
Phil  [Δημιουργός] 3 Ιουλ, 7:12 
Throttle is throttle, you need to add fuel manifold throttle which without supercharge can just be half of the air throttle.
CatLover2500 2 Ιουλ, 13:34 
Does it work with modular engines?
__MRX__ 31 Μαρ, 6:20 
you should add idle rps
Firegecko 14 Δεκ 2023, 0:16 
Awesome. Just what i was needing. Thanks heaps!
Decadenced 6 Αυγ 2023, 10:25 
works fine 4 me, thank u
Phil  [Δημιουργός] 28 Ιουν 2023, 9:56 
No it doesn't, just an RPS limiter like the name says, not an ECU. To idle engine you could just switchbox to a PID with P of 0.3.
buder28 27 Ιουν 2023, 14:16 
that mcu dosent have any kind of idling controll last time i tested
you will need to figure that out
Ninovium 27 Ιουν 2023, 13:39 
btw if you connect an actual throttle to the controller, then the engine just goes to 1 rps and dies. If you connect to W/S, it revs the engine to the max until it explodes. (it also implodes your ear drums)
Ninovium 27 Ιουν 2023, 13:37 
I have the same problem as the guy below, could you show us how to actually connect it? (to help idiots like myself)
BasicallyIPlayGames 8 Ιουν 2023, 20:47 
Other than its set up with W/S but I'd imagine it should still work set up like that still.