Butiksside
Stormworks: Build and Rescue
Alt Diskussioner Skærmbilleder Illustrationer Broadcasts Videoer Værksted Nyheder Guider Anmeldelser

Stormworks: Build and Rescue

Butiksside
Stormworks: Build and Rescue >  Værksted > Phils værksted
31 vurderinger
Smooth RPS Limiter (Modular Engines and Prefabs)
Beskrivelse Diskussioner0 Kommentarer30 Ændringsbemærkninger
   
Pris
Føj til foretrukne
Gjort til foretrukken
Fjern som foretrukken
Vehicles: Air, Sea, Land, Mechanical
Microcontrollers: Calculation, Fluid, Modular, Microcontroller
Tags: v1.2.3
Filstørrelse:
Offentliggjort:
Opdateret:
164.550 KB
13. juni 2021 kl. 13:00
13. juni 2021 kl. 13:21
2 ændringsbemærkninger ( vis )
Designet af:
Phil
Offline
Se alle 20 samlinger (nogle kan være skjulte)
2,684 Unikke besøgende
1,327 Nuværende abonnenter
30 Nuværende foretrukne

Abonner for at downloade
Smooth RPS Limiter (Modular Engines and Prefabs)

Beskrivelse
If you are unhappy with the 0.5 method consisting in cutting the throttle in half if the RPS are above the set limit, try out this Microcontroller! (No PID inside!)
With this smooth approach you can get a more continuous engine throttle resulting in less fuel consumption and heat generation as well as less unpleasant engine noise.

You can enable variable RPS limit to change that limit in-game while on the move.
A hardness factor is determined by your set RPS limit to keep the resulting RPS from overshooting more than 1. You can manually increase that factor if you want to be closer to the RPS limit.

This controller works on no load engines too but is meant for engines under load like vehicle engines.
30 kommentarer
< >
Phil  [ophavsmand] 3. juli kl. 7:12 
Throttle is throttle, you need to add fuel manifold throttle which without supercharge can just be half of the air throttle.
CatLover2500 2. juli kl. 13:34 
Does it work with modular engines?
__MRX__ 31. mar. kl. 6:20 
you should add idle rps
Firegecko 14. dec. 2023 kl. 0:16 
Awesome. Just what i was needing. Thanks heaps!
Decadenced 6. aug. 2023 kl. 10:25 
works fine 4 me, thank u
Phil  [ophavsmand] 28. juni 2023 kl. 9:56 
No it doesn't, just an RPS limiter like the name says, not an ECU. To idle engine you could just switchbox to a PID with P of 0.3.
buder28 27. juni 2023 kl. 14:16 
that mcu dosent have any kind of idling controll last time i tested
you will need to figure that out
Ninovium 27. juni 2023 kl. 13:39 
btw if you connect an actual throttle to the controller, then the engine just goes to 1 rps and dies. If you connect to W/S, it revs the engine to the max until it explodes. (it also implodes your ear drums)
Ninovium 27. juni 2023 kl. 13:37 
I have the same problem as the guy below, could you show us how to actually connect it? (to help idiots like myself)
BasicallyIPlayGames 8. juni 2023 kl. 20:47 
Other than its set up with W/S but I'd imagine it should still work set up like that still.