Obchod
Stormworks: Build and Rescue
Vše Diskuze Snímky obrazovky Obrázky Přenosy Videa Workshop Novinky Návody Recenze

Stormworks: Build and Rescue

Obchod
Stormworks: Build and Rescue >  Workshop > Workshop uživatele Phil
31 hodnocení
Smooth RPS Limiter (Modular Engines and Prefabs)
Popis Diskuze0 Komentáře30 Poznámky ke změnám
   
Ocenit
Přidat do oblíbených
Oblíbeno
Odebrat z oblíbených
Vehicles: Air, Sea, Land, Mechanical
Microcontrollers: Calculation, Fluid, Modular, Microcontroller
Značky: v1.2.3
Velikost souboru
Přidáno
Aktualizováno
164.550 KB
13. čvn. 2021 v 13.00
13. čvn. 2021 v 13.21
Poznámky ke změnám (2) – zobrazit
Vytvořil
Phil
Offline
Prohlédněte si všechny kolekce (20), z nichž některé mohou být skryté
2,684 unikátních návštěvníků
1,327 odběratelů
30 přidání do oblíbených

Klikněte na „Odebírat“ pro stažení položky
Smooth RPS Limiter (Modular Engines and Prefabs)

Popis
If you are unhappy with the 0.5 method consisting in cutting the throttle in half if the RPS are above the set limit, try out this Microcontroller! (No PID inside!)
With this smooth approach you can get a more continuous engine throttle resulting in less fuel consumption and heat generation as well as less unpleasant engine noise.

You can enable variable RPS limit to change that limit in-game while on the move.
A hardness factor is determined by your set RPS limit to keep the resulting RPS from overshooting more than 1. You can manually increase that factor if you want to be closer to the RPS limit.

This controller works on no load engines too but is meant for engines under load like vehicle engines.
Počet komentářů: 30
< >
Phil  [autor] 3. čvc. v 7.12 
Throttle is throttle, you need to add fuel manifold throttle which without supercharge can just be half of the air throttle.
CatLover2500 2. čvc. v 13.34 
Does it work with modular engines?
__MRX__ 31. bře. v 6.20 
you should add idle rps
Firegecko 14. pro. 2023 v 0.16 
Awesome. Just what i was needing. Thanks heaps!
Decadenced 6. srp. 2023 v 10.25 
works fine 4 me, thank u
Phil  [autor] 28. čvn. 2023 v 9.56 
No it doesn't, just an RPS limiter like the name says, not an ECU. To idle engine you could just switchbox to a PID with P of 0.3.
buder28 27. čvn. 2023 v 14.16 
that mcu dosent have any kind of idling controll last time i tested
you will need to figure that out
Ninovium 27. čvn. 2023 v 13.39 
btw if you connect an actual throttle to the controller, then the engine just goes to 1 rps and dies. If you connect to W/S, it revs the engine to the max until it explodes. (it also implodes your ear drums)
Ninovium 27. čvn. 2023 v 13.37 
I have the same problem as the guy below, could you show us how to actually connect it? (to help idiots like myself)
BasicallyIPlayGames 8. čvn. 2023 v 20.47 
Other than its set up with W/S but I'd imagine it should still work set up like that still.