Kauppasivu
Stormworks: Build and Rescue
Kaikki Keskustelut Kuvakaappaukset Taideteokset Suoratoistot Videot Workshop Uutiset Oppaat Arvostelut

Stormworks: Build and Rescue

Kauppasivu
Stormworks: Build and Rescue >  Workshop > Käyttäjän Olaroll Workshop
57 arvostelua
Velocity Pivot to Robotic Pivot
Kuvaus Keskustelut0 Kommentit35 Muutokset
2
2
2
   
Palkinto
Lisää suosikkeihin
Lisätty suosikkeihin
Poista suosikeista
Vehicles: Mechanical
Microcontrollers: Microcontroller
Tunnisteet: v0.10.17
Tiedostokoko
Julkaistu
Päivitetty
29.121 KB
9.2.2020 klo 17.08
10.5.2020 klo 18.03
6 muutosilmoitusta ( näytä )
Tekijä
Olaroll
Kirjautunut ulos
Näytä kaikki 78 kokoelmaa
5,972 Uniikkeja kävijöitä
4,004 Nykyiset tilaajat
60 Nykyiset suosikit

Tilaa ladataksesi
Velocity Pivot to Robotic Pivot

Kuvaus
Turns a velocity pivot into a fully configurable robotic one.

By default, it'll behave just like a robotic pivot, except much faster while remaining smooth.

Here's all the configuration options and what they do:
  1. Pivot Gear Ratio - Set this to your pivot's gear ratio
  2. Rotation Limit - Enables rotation limiting
  3. Max & Min Degrees - Can be independently adjusted
  4. Relative Mode - If on, it'll map a 0 to 1 or -1 to 1 input onto the min/max range set before. If off, it'll take an absolute input in full turns, clamped to the limits.
  5. Relative Input - Sets the relative input range, as mentioned before.
  6. Positive/Negative Rotation Time - Individually set the time it takes for it to move from current to target position
  7. Speed Limit - Set a speed limit in RPS. It is ignored if at 0
  8. PID Multiplier - Multiplies the PID output. (I only recommend lowering this, if the default of 1x has instability)
35 kommenttia
< >
Spongbob 29.12.2024 klo 17.41 
can this be clamped?
EphainKartur 7.11.2024 klo 13.57 
* there is some logic between the throttle lever and the chair axes, to convert the chair axis controls into on/off, to go into the throttle levers
EphainKartur 7.11.2024 klo 13.56 
im using this for a turret im making (it works great after a little bit of tuning, i have it going from chair axis -> throttle lever -> this controller -> pivot), however, im thinking of cutting out the greater than, less than, and switchbox logic, as well as the throttle lever, and keeping the rotation continuous. but, im unsure what to do. does the controller allow continuous rotation? really, i need the controller to accept on/off inputs for positive /negative rotation, rather than a number, and the sensitivity for this motion to be tuneable.
Grande1900 15.6.2024 klo 7.08 
@CRUSADER that's because lua can directly read properties without needing a connection
CRUSADER 7.5.2024 klo 0.25 
Well, the rotation limit can't be turned off, went in to check, and it's not even connected to anything, 👍
LionsFan20 21.4.2024 klo 12.26 
Does this work for Compact Velocity Pivots and Turret Rings?
NickName 12.4.2024 klo 6.44 
very very buggy. I want to use it for a turret but using this creates some force pushing my hull around
Nick Name 1.12.2023 klo 17.52 
is there a way to make this work, but with small pivots and the phys sensor?
Ncplq 11.11.2023 klo 6.09 
https://steamproxy.net/id/fiz9/myworkshopfiles/?appid=573090
HI! I added an ability to invert rotation. If you add it to the original, I'll delete mine/
Breezing 24.10.2023 klo 19.19 
can you use this to make boosters guidable from pivots