Butikksiden
Space Engineers
Alle Diskusjoner Skjermbilder Kunstverk Kringkastninger Videoer Workshop Nyheter Veiledninger Anmeldelser

Space Engineers

Butikksiden
Space Engineers >  Workshop > Workshopen til Icen
94 vurderinger
Half Ramps (now with DX11!)
Beskrivelse Diskusjoner0 Kommentarer64 Endringslogger
   
Utmerkelse
Favoritt
Favoritter
Fjern som favoritt
Type: Mod
Mod category: Block
Filstørrelse
Lagt ut
Oppdatert
525.993 KB
7. sep. 2014 kl. 14.06
13. des. 2015 kl. 7.30
3 endringslogger ( vis )
Laget av
Icen
Frakoblet
Se alle 401 samlinger (noen kan være skjult)
8,393 Unike besøkende
3,983 Nåværende abonnenter
152 Nåværende favoritter

Abonner for å laste ned
Half Ramps (now with DX11!)

Beskrivelse
I made this mod mainly because I needed to have it sliced in the middle, but there wasn't any mod like this. There was some interest over this mod at the Keen Software House forums (http://forums.keenswh.com), which made me want to go a bit more on this, not just the final cube, but the construction models too.
The people at keenswh forums were a great help! Could not have managed this without you people! Thanks! :D

These blocks are for big grids, not for small ships.


This mod is now supporting DX11!
Special thanks for The Witch for helping out!

Keep on spengineering!
64 kommentarer
< >
Mojo 13. des. 2015 kl. 10.30 
Glad I was able to help in getting these updated to DX11. :)
Mojo 12. des. 2015 kl. 17.07 
I could get these updated for you in 5 mins tops :)
Parszywy Lisi Bobek 2. des. 2015 kl. 4.04 
WHAT I SEE?! I'M SO HAPPY THAT THIS MOD WILL GET BACK INTO USE! :DD
Icen  [skaper] 30. nov. 2015 kl. 1.19 
That would actually help me a ton, if you were to fix the textures for me. I could add you as a contributor then. So you wouldn't be having to remake it all, how would you like to get the files from me?
Rhedd 29. nov. 2015 kl. 18.43 
If you could get it working, it would save me from having to remake these from scratch, which I was starting to think about doing. :P
Rhedd 29. nov. 2015 kl. 18.42 
Your texture definitions in the block's XML are going to be different, as well, because DX11 textures have different names.
It might very well work, however, if you copy the new ramp textures into your mod, and then just copy/paste the appropriate texture section into your XML from the vanilla ramp.
Give it a try. It might be that easy! ^_^
Icen  [skaper] 29. nov. 2015 kl. 12.09 
I took a peek at conversion to DX11 and ran into some problems. I used the XML updater, sure, but the textures won't update properly to the new textures. I read that the converter had some hickup, but as I had used the original ramp textures for both of these ramp pieces, I thought it would work if I copied the new files in. That was not the case, it didn't work.

Does anyone have any ideas on how to fix this? Couldn't find any working solution to this. Will look more into this later in december.
737✈Garrus 29. nov. 2015 kl. 7.49 
Please DX11!!!
Roman Cat 14. nov. 2015 kl. 6.06 
dx11 please
Rhedd 7. sep. 2015 kl. 5.40 
This mod is still VERY useful. The vanilla half-ramps are armor. These are half of the ramp piece, so if you want them to match visually (I do) then you still have to use these.

I do wish for some half vanilla stairs, though. That's be nice.