Pagina din magazin
Space Engineers
Toate Discuții Capturi de ecran Ilustrații Difuzări Videoclipuri Atelier Știri Ghiduri Recenzii

Space Engineers

Pagina din magazin
Space Engineers >  Atelier > Atelierul lui Mork
Evaluări insuficiente
IMP Air Large Miner PAM
Descriere Discuții0 Comentarii6 Notițe privind schimbările
   
Premiază
Adaugă la preferate
Preferat
Elimină din preferate
Type: Blueprint
Mod category: Exploration
Dimensiunea fișierului
Postat
Actualizat
2.583 MB
22 sept. 2019 la 0:41
12 ian. 2020 la 13:41
4 notițe privind schimbările ( vizionare )
Creat de
Mork
Online
Afișează toate cele 3 colecții create de Mork și alți jucători (unele pot fi ascunse)
571 Vizitatori unici
157 Abonați actuali
3 Preferate

Abonează-te pentru a descărca
IMP Air Large Miner PAM

În 1 colecție creată de Mork
IMP Commercial Shipyards
49 obiecte
Descriere
IMP Large aerial PAM vertical tunnel miner, Vanilla, Survival, Printable.
8,589 PCU

Printable top to bottom.
Printable from rear to front but you would need a sprue to connect the bottom drills to the top thruster.
42 Drills and some small cargo containers.
No stone ejector.
Front dock and remote camera, Bottom PAM targeting camera.
Cockpit with status, PAM and ore displays.
Self repair projector with pre-loaded blueprint turned off.
Remote control with camera, no cockpit display information.
Tested with full ore load on earth. Not sure how high you can fly while fully loaded.

Control bars setup for main cockpit and remote control
In both cases control bar 1 is normal flying, control bar 2 is for PAM operations
Most of the control bar is self explanatory except the following.
Control bar 1 both manual and remote
4 Hover Aligner On
5 Hover Aligner Off
Control bar 2 PAM both manual and remote
1 PAM up
2 PAM down
3 PAM apply
4 Hover Aligner On
5 Hover Aligner Off

Warning: while you can fly around with the hover aligner manually and when pathing for the PAM script.
Disable the hover aligner before activating PAM automining as missing thrust due to the hover aligner
may cause the miner to crash.

Can be used as a manual or remote miner without scripts. Might need to change the antenna range though.

MMaster's Automatic LCD's 2 (disabled when docked)
https://steamproxy.net/sharedfiles/filedetails/?id=822950976

p3st|cIdE's Hover Aligner
https://steamproxy.net/sharedfiles/filedetails/?id=583272553

Keks's PAM script
https://steamproxy.net/sharedfiles/filedetails/?id=1507646929
6 comentarii
< >
Mork  [autor] 28 ian. 2020 la 0:31 
It means check the same grid only. Don't add up the attached grids. Like the base your docked to.
Blackbeard 27 ian. 2020 la 23:13 
Thx a lot! What does the T: does?
Mork  [autor] 27 ian. 2020 la 12:03 
You can grab it from the cockpit customdata. The first line tells it which screen to use then what the contents of that LCD should be. The rest that I left out was the stuff for the right LCD.
@1 AutoLCD
PowerUsedV T:*
PowerStoredP T:Battery
PowerTime T:*
CargoAll T:*
ShipMass T:*
DateTime
Pos
Damage
Blackbeard 26 ian. 2020 la 12:55 
Yes it is awesome! I want to know what commands you used in the customdata to show it on the screen. I havent build anything to print me a ship, thats why I was asking you directly, but probarly you dont remember because its on the workshop since September
Mork  [autor] 26 ian. 2020 la 12:44 
That was MMaster's Automatic LCD script which is a nice one. The commands for that are in the customdata of the LCD. Just need the same tag in the name on the LCD as the one the script updates. It then reads the customdata of the LCD to update it.
Blackbeard 26 ian. 2020 la 12:24 
Hey There! What commands do you use for the LCDs? The Center is clear, but the left one is pretty nice