Strona w sklepie
Space Engineers
Wszystko Dyskusje Zrzuty ekranu Prace graficzne Transmisje Wideo Warsztat Aktualności Poradniki Recenzje

Space Engineers

Strona w sklepie
Space Engineers >  Warsztat > Warsztat użytkownika Mork
Zbyt mało ocen
IMP Air Large Miner PAM
Opis Dyskusje0 Komentarze6 Lista zmian
   
Przyznaj nagrodę
Ulubione
Ulubione
Usuń z ulubionych
Type: Blueprint
Mod category: Exploration
Rozmiar pliku
Zamieszczono
Zaktualizowano
2.583 MB
22 września 2019 o 0:41
12 stycznia 2020 o 13:41
Listy zmian: 4 ( zobacz )
Twórca
Mork
Online
Zobacz wszystkie kolekcje (3) stworzone przez Mork oraz innych użytkowników (niektóre mogą być ukryte)
563 Unikalni odwiedzający
157 Obecni subskrybenci
3 Obecne ulubione

Zasubskrybuj, aby pobrać
IMP Air Large Miner PAM

W 1 kolekcji stworzonej przez Mork
IMP Commercial Shipyards
Przedmioty: 49
Opis
IMP Large aerial PAM vertical tunnel miner, Vanilla, Survival, Printable.
8,589 PCU

Printable top to bottom.
Printable from rear to front but you would need a sprue to connect the bottom drills to the top thruster.
42 Drills and some small cargo containers.
No stone ejector.
Front dock and remote camera, Bottom PAM targeting camera.
Cockpit with status, PAM and ore displays.
Self repair projector with pre-loaded blueprint turned off.
Remote control with camera, no cockpit display information.
Tested with full ore load on earth. Not sure how high you can fly while fully loaded.

Control bars setup for main cockpit and remote control
In both cases control bar 1 is normal flying, control bar 2 is for PAM operations
Most of the control bar is self explanatory except the following.
Control bar 1 both manual and remote
4 Hover Aligner On
5 Hover Aligner Off
Control bar 2 PAM both manual and remote
1 PAM up
2 PAM down
3 PAM apply
4 Hover Aligner On
5 Hover Aligner Off

Warning: while you can fly around with the hover aligner manually and when pathing for the PAM script.
Disable the hover aligner before activating PAM automining as missing thrust due to the hover aligner
may cause the miner to crash.

Can be used as a manual or remote miner without scripts. Might need to change the antenna range though.

MMaster's Automatic LCD's 2 (disabled when docked)
https://steamproxy.net/sharedfiles/filedetails/?id=822950976

p3st|cIdE's Hover Aligner
https://steamproxy.net/sharedfiles/filedetails/?id=583272553

Keks's PAM script
https://steamproxy.net/sharedfiles/filedetails/?id=1507646929
Komentarzy: 6
< >
Mork  [autor] 28 stycznia 2020 o 0:31 
It means check the same grid only. Don't add up the attached grids. Like the base your docked to.
Blackbeard 27 stycznia 2020 o 23:13 
Thx a lot! What does the T: does?
Mork  [autor] 27 stycznia 2020 o 12:03 
You can grab it from the cockpit customdata. The first line tells it which screen to use then what the contents of that LCD should be. The rest that I left out was the stuff for the right LCD.
@1 AutoLCD
PowerUsedV T:*
PowerStoredP T:Battery
PowerTime T:*
CargoAll T:*
ShipMass T:*
DateTime
Pos
Damage
Blackbeard 26 stycznia 2020 o 12:55 
Yes it is awesome! I want to know what commands you used in the customdata to show it on the screen. I havent build anything to print me a ship, thats why I was asking you directly, but probarly you dont remember because its on the workshop since September
Mork  [autor] 26 stycznia 2020 o 12:44 
That was MMaster's Automatic LCD script which is a nice one. The commands for that are in the customdata of the LCD. Just need the same tag in the name on the LCD as the one the script updates. It then reads the customdata of the LCD to update it.
Blackbeard 26 stycznia 2020 o 12:24 
Hey There! What commands do you use for the LCDs? The Center is clear, but the left one is pretty nice