Página de la tienda
Space Engineers
Todo Discusiones Capturas Artwork Retransmisiones Videos Workshop Noticias Guías Reseñas

Space Engineers

Página de la tienda
Space Engineers >  Workshop > Workshop de Mork
No hay suficientes valoraciones
IMP Air Large Miner PAM
Descripción Discusiones0 Comentarios6 Notas sobre cambios
   
Premio
Favoritos
Favorito
Quitar
Type: Blueprint
Mod category: Exploration
Tamaño
Publicado el
Actualizado el
2.583 MB
22 SEP 2019 a las 12:41 a. m.
12 ENE 2020 a las 1:41 p. m.
4 notas sobre cambios ( ver )
Creado por
Mork
En línea
Ver las 3 colecciones creadas por Mork y otros (algunas podrían estar ocultas)
571 Visitantes únicos
157 Suscriptores actuales
3 Favoritos actuales

Suscríbete para descargar
IMP Air Large Miner PAM

En 1 colección creada por Mork
IMP Commercial Shipyards
49 artículos
Descripción
IMP Large aerial PAM vertical tunnel miner, Vanilla, Survival, Printable.
8,589 PCU

Printable top to bottom.
Printable from rear to front but you would need a sprue to connect the bottom drills to the top thruster.
42 Drills and some small cargo containers.
No stone ejector.
Front dock and remote camera, Bottom PAM targeting camera.
Cockpit with status, PAM and ore displays.
Self repair projector with pre-loaded blueprint turned off.
Remote control with camera, no cockpit display information.
Tested with full ore load on earth. Not sure how high you can fly while fully loaded.

Control bars setup for main cockpit and remote control
In both cases control bar 1 is normal flying, control bar 2 is for PAM operations
Most of the control bar is self explanatory except the following.
Control bar 1 both manual and remote
4 Hover Aligner On
5 Hover Aligner Off
Control bar 2 PAM both manual and remote
1 PAM up
2 PAM down
3 PAM apply
4 Hover Aligner On
5 Hover Aligner Off

Warning: while you can fly around with the hover aligner manually and when pathing for the PAM script.
Disable the hover aligner before activating PAM automining as missing thrust due to the hover aligner
may cause the miner to crash.

Can be used as a manual or remote miner without scripts. Might need to change the antenna range though.

MMaster's Automatic LCD's 2 (disabled when docked)
https://steamproxy.net/sharedfiles/filedetails/?id=822950976

p3st|cIdE's Hover Aligner
https://steamproxy.net/sharedfiles/filedetails/?id=583272553

Keks's PAM script
https://steamproxy.net/sharedfiles/filedetails/?id=1507646929
6 comentarios
< >
Mork  [autor] 28 ENE 2020 a las 12:31 a. m. 
It means check the same grid only. Don't add up the attached grids. Like the base your docked to.
Blackbeard 27 ENE 2020 a las 11:13 p. m. 
Thx a lot! What does the T: does?
Mork  [autor] 27 ENE 2020 a las 12:03 p. m. 
You can grab it from the cockpit customdata. The first line tells it which screen to use then what the contents of that LCD should be. The rest that I left out was the stuff for the right LCD.
@1 AutoLCD
PowerUsedV T:*
PowerStoredP T:Battery
PowerTime T:*
CargoAll T:*
ShipMass T:*
DateTime
Pos
Damage
Blackbeard 26 ENE 2020 a las 12:55 p. m. 
Yes it is awesome! I want to know what commands you used in the customdata to show it on the screen. I havent build anything to print me a ship, thats why I was asking you directly, but probarly you dont remember because its on the workshop since September
Mork  [autor] 26 ENE 2020 a las 12:44 p. m. 
That was MMaster's Automatic LCD script which is a nice one. The commands for that are in the customdata of the LCD. Just need the same tag in the name on the LCD as the one the script updates. It then reads the customdata of the LCD to update it.
Blackbeard 26 ENE 2020 a las 12:24 p. m. 
Hey There! What commands do you use for the LCDs? The Center is clear, but the left one is pretty nice