Page du magasin
Space Engineers
Tous Discussions Captures d'écran Créations de fans Diffusions Vidéos Workshop Actualités Guides Évaluations

Space Engineers

Page du magasin
Space Engineers >  Workshop > Workshop de Mork
Pas assez d'évaluations
IMP Air Large Miner PAM
Description Discussions0 Commentaires6 Notes de changement
   
Récompenser
Ajouter aux favoris
Favoris
Retirer des favoris
Type: Blueprint
Mod category: Exploration
Taille du fichier
Publié le
Mis à jour le
2.583 MB
22 sept. 2019 à 0h41
12 janv. 2020 à 13h41
4 notes de changement ( voir )
Créé par
Mork
En ligne
Voir les 3 collections créées par Mork et d'autres personnes (certaines peuvent être cachées)
563 Visites uniques
157 Abonné(e)s
3 Favoris actuels

S'abonner pour télécharger
IMP Air Large Miner PAM

Dans 1 collection faite par Mork
IMP Commercial Shipyards
49 objets
Description
IMP Large aerial PAM vertical tunnel miner, Vanilla, Survival, Printable.
8,589 PCU

Printable top to bottom.
Printable from rear to front but you would need a sprue to connect the bottom drills to the top thruster.
42 Drills and some small cargo containers.
No stone ejector.
Front dock and remote camera, Bottom PAM targeting camera.
Cockpit with status, PAM and ore displays.
Self repair projector with pre-loaded blueprint turned off.
Remote control with camera, no cockpit display information.
Tested with full ore load on earth. Not sure how high you can fly while fully loaded.

Control bars setup for main cockpit and remote control
In both cases control bar 1 is normal flying, control bar 2 is for PAM operations
Most of the control bar is self explanatory except the following.
Control bar 1 both manual and remote
4 Hover Aligner On
5 Hover Aligner Off
Control bar 2 PAM both manual and remote
1 PAM up
2 PAM down
3 PAM apply
4 Hover Aligner On
5 Hover Aligner Off

Warning: while you can fly around with the hover aligner manually and when pathing for the PAM script.
Disable the hover aligner before activating PAM automining as missing thrust due to the hover aligner
may cause the miner to crash.

Can be used as a manual or remote miner without scripts. Might need to change the antenna range though.

MMaster's Automatic LCD's 2 (disabled when docked)
https://steamproxy.net/sharedfiles/filedetails/?id=822950976

p3st|cIdE's Hover Aligner
https://steamproxy.net/sharedfiles/filedetails/?id=583272553

Keks's PAM script
https://steamproxy.net/sharedfiles/filedetails/?id=1507646929
6 commentaires
< >
Mork  [créateur] 28 janv. 2020 à 0h31 
It means check the same grid only. Don't add up the attached grids. Like the base your docked to.
Blackbeard 27 janv. 2020 à 23h13 
Thx a lot! What does the T: does?
Mork  [créateur] 27 janv. 2020 à 12h03 
You can grab it from the cockpit customdata. The first line tells it which screen to use then what the contents of that LCD should be. The rest that I left out was the stuff for the right LCD.
@1 AutoLCD
PowerUsedV T:*
PowerStoredP T:Battery
PowerTime T:*
CargoAll T:*
ShipMass T:*
DateTime
Pos
Damage
Blackbeard 26 janv. 2020 à 12h55 
Yes it is awesome! I want to know what commands you used in the customdata to show it on the screen. I havent build anything to print me a ship, thats why I was asking you directly, but probarly you dont remember because its on the workshop since September
Mork  [créateur] 26 janv. 2020 à 12h44 
That was MMaster's Automatic LCD script which is a nice one. The commands for that are in the customdata of the LCD. Just need the same tag in the name on the LCD as the one the script updates. It then reads the customdata of the LCD to update it.
Blackbeard 26 janv. 2020 à 12h24 
Hey There! What commands do you use for the LCDs? The Center is clear, but the left one is pretty nice