Trang cửa hàng
Stormworks: Build and Rescue
Tất cả Thảo luận Ảnh chụp Tranh ảnh Phát sóng Video Workshop Tin tức Hướng dẫn Đánh giá

Stormworks: Build and Rescue

Trang cửa hàng
Stormworks: Build and Rescue >  Workshop > Workshop của Tajin
Không đủ lượt đánh giá
Logic: Altitude hold example (PID based)
Mô tả Thảo luận0 Bình luận14 Ghi chú thay đổi
   
Giải thưởng
Yêu thích
Đã yêu thích
Bỏ thích
Vehicles: Vehicle, Air, Exploration, Technical
Nhãn: v0.3.3
Kích cỡ file
Đã đăng
Đã cập nhật
43.323 KB
8 Thg05, 2018 @ 3:01am
3 Thg08, 2018 @ 2:01pm
3 ghi chú thay đổi ( xem )
Tạo bởi
Tajin
Trên mạng
Xem tất cả 15 bộ sưu tập tạo bởi Tajin và những người khác (một số có thể bị ẩn)
891 Số khách thăm độc nhất
473 Người đăng ký hiện tại
4 Lượt yêu thích

Đăng ký để tải xuống
Logic: Altitude hold example (PID based)

Trong 1 bộ sưu tập tạo bởi Tajin
Logic Examples & Knowhow
54 vật phẩm
Mô tả
# Small example helicopter with a toggleable altitude hold system. #
This variant uses a PID for the altitude. PIDs are much harder to set up than a GYRO but can be tuned to pretty much any application. I'd suggest to try and see if the GYRO variant works for your vehicle and utilize the PID only if youre familiar with it or if the GYRO doesn't work well.

- - - - -

The helicopter uses as sticky collective controlled via W/S.
3 toggles the ALT hold, the controls are labeled.

Note that with the ALT hold engaged you can still make minor adjustments around the set altitude, by changing the collective. Throttle in this example is fixed to 1.


Gates relevant to the altitude hold are colored blue.
The clamp gate is just a safety measure. Small helicopters have a tendency to flip over when the collective is lowered to fast.
14 bình luận
< >
syrenevice 16 Thg05, 2019 @ 11:46pm 
Nice and simple works.
It takes easy to understand.
Thanks!!
Sgt. Max Cockburn 19 Thg09, 2018 @ 4:25am 
OK, I think I understand that.

Not sure what the "collective" represents, as I'm still unsure what several other concepts and modules represent. That makes it hard to figure stuff out.

I copied your system on my chopper and it works, just not sure why lol.

Thanks for your time.
Sgt. Max Cockburn 18 Thg09, 2018 @ 9:33am 
And what does that accomplish? What's the reasoning behind "combining" the outputs? I'm completely stuck lol.

I more or less tried to replicate this just now, but it still doesn't do anything for me. I just have up/down fed into Add B, otherwise it's the same - just without the clam.

Tajin  [tác giả] 18 Thg09, 2018 @ 9:00am 
the "add" simply combines the output from the pid with the output from the pilot seat,
Sgt. Max Cockburn 18 Thg09, 2018 @ 8:05am 
What is the use of the Add logic component? I think it's why I can't get my system to work.
SamuelPepys 30 Thg07, 2018 @ 5:41pm 
Ah, ok. I got it, I just needed to adjust the PID values and the value being sent to the collective. I just put the differential up to super high levels (7 I think), the proportional quite low and then adjusted the clamp gate numbers down to make the helicopter not free fall once I used the keypad to enter a lower altitude. Everything works awesomely now!
SamuelPepys 30 Thg07, 2018 @ 3:13pm 
Hi! The system makes the helicopter spin around violently and uncontrollably. I am using a keypad to control altitude, and I think it has to do with the speed that it tries to acchieve the altitude. Is there a way to reduce the speed of which it tries to compensate?
Tajin  [tác giả] 30 Thg07, 2018 @ 10:05am 
Logic in this one stores the current altitude in a memory gate. So just replace that with a keypad to enter your desired altitude.
MW-777 26 Thg07, 2018 @ 7:12am 
is there a way of making it so i type an altitude i want and it takes me to it and holds that altituse?
if you know what i mean :)
Poyo the pepsi boi 23 Thg07, 2018 @ 5:02am 
ah i got you.
thank you :)