Áruházi oldal

Stormworks: Build and Rescue

Összes Témák Képernyőmentések Alkotások Közvetítések Videók Műhely Hírek Útmutatók Értékelések

Stormworks: Build and Rescue > Műhely > Tajin Műhelye

Nincs elegendő értékelés

Logic: Altitude hold example (PID based)

Leírás Témák0 Megjegyzések14 Változásjegyzék

Díjazás

Vehicles: Vehicle, Air, Exploration, Technical

Címkék: v0.3.3

Fájlméret:

Közzétéve:

Frissítve:

43.323 KB

2018. máj. 8., 3:01

2018. aug. 3., 14:01

3 változásjegyzék ( megnézés )

882	egyedi látogató
474	jelenlegi feliratkozó
4	ember kedvence jelenleg

Feliratkozás a letöltéshez
Logic: Altitude hold example (PID based)

Feliratkozva

Leiratkozás

1 Tajin készítette gyűjteményben

Logic Examples & Knowhow

54 elem

Leírás

# Small example helicopter with a toggleable altitude hold system. #
This variant uses a PID for the altitude. PIDs are much harder to set up than a GYRO but can be tuned to pretty much any application. I'd suggest to try and see if the GYRO variant works for your vehicle and utilize the PID only if youre familiar with it or if the GYRO doesn't work well.

- - - - -

The helicopter uses as sticky collective controlled via W/S.
3 toggles the ALT hold, the controls are labeled.

Note that with the ALT hold engaged you can still make minor adjustments around the set altitude, by changing the collective. Throttle in this example is fixed to 1.

Gates relevant to the altitude hold are colored blue.
The clamp gate is just a safety measure. Small helicopters have a tendency to flip over when the collective is lowered to fast.

14 megjegyzés

< >

syrenevice 2019. máj. 16., 23:46

Nice and simple works.
It takes easy to understand.
Thanks!!

Sgt. Max Cockburn 2018. szept. 19., 4:25

OK, I think I understand that.

Not sure what the "collective" represents, as I'm still unsure what several other concepts and modules represent. That makes it hard to figure stuff out.

I copied your system on my chopper and it works, just not sure why lol.

Thanks for your time.

Sgt. Max Cockburn 2018. szept. 18., 9:33

And what does that accomplish? What's the reasoning behind "combining" the outputs? I'm completely stuck lol.

I more or less tried to replicate this just now, but it still doesn't do anything for me. I just have up/down fed into Add B, otherwise it's the same - just without the clam.

Tajin [készítő] 2018. szept. 18., 9:00

the "add" simply combines the output from the pid with the output from the pilot seat,

Sgt. Max Cockburn 2018. szept. 18., 8:05

What is the use of the Add logic component? I think it's why I can't get my system to work.

SamuelPepys 2018. júl. 30., 17:41

Ah, ok. I got it, I just needed to adjust the PID values and the value being sent to the collective. I just put the differential up to super high levels (7 I think), the proportional quite low and then adjusted the clamp gate numbers down to make the helicopter not free fall once I used the keypad to enter a lower altitude. Everything works awesomely now!

SamuelPepys 2018. júl. 30., 15:13

Hi! The system makes the helicopter spin around violently and uncontrollably. I am using a keypad to control altitude, and I think it has to do with the speed that it tries to acchieve the altitude. Is there a way to reduce the speed of which it tries to compensate?

Tajin [készítő] 2018. júl. 30., 10:05

Logic in this one stores the current altitude in a memory gate. So just replace that with a keypad to enter your desired altitude.

MW-777 2018. júl. 26., 7:12

is there a way of making it so i type an altitude i want and it takes me to it and holds that altituse?
if you know what i mean :)

Poyo the pepsi boi 2018. júl. 23., 5:02

ah i got you.
thank you :)

< >

Stormworks: Build and Rescue

Feliratkozás a letöltéshezLogic: Altitude hold example (PID based)

Hivatkozások szerkesztése

Feliratkozás a letöltéshez
Logic: Altitude hold example (PID based)